The DJI Air 3 is at present lower than a 12 months outdated with many new to flying drones, lovers, content material creators, and veterans having fun with frequently flying and producing content material with it.
Nonetheless, although comparatively younger, the Air 3 may encounter a hiccup or two or could also be gifted or bought to another person this season.
With this in thoughts, can the Air 3 and its accompanying distant controllers be manufacturing facility reset?
Sadly, the DJI Air 3 can’t be manufacturing facility reset. Nonetheless, I’ll focus on rolling again the Air 3 and DJI RC 2’s firmware, when accessible, with the DJI Assistant 2 software program. Moreover, I’ll go over the steps wanted to organize the Air 3 for gifting or promoting: which incorporates unbinding gadgets and deleting profiles.
Allow us to take a deeper have a look at these steps.
DJI Assistant 2 (Client Drone Sequence)
The DJI Assistant 2 (Client Drone Sequence) software program was created by DJI to be used with lots of its shopper drones to carry out varied duties.
The duty we’re involved with for this text can be rolling again firmware updates, if and when accessible.
For earlier fashions of DJI drones utilizing the Assistant 2 software program, there have been certainly choices for bringing a drone again to beforehand launched firmware variations.
As of this text’s writing, there have been no earlier Air 3 firmware variations which are accessible to roll again to. Nonetheless, within the close to future, when and if this selection turns into accessible, the steps are lined right here.
» MORE: Does DJI Assistant Work with Air 3 (Answered – With Video)
Downloading & Putting in DJI Assistant 2
To obtain the DJI Assistant 2 software program for the Air 3, choose one of many two following hyperlinks to your laptop kind:
After you will have downloaded the software program, set up it utilizing the strategies of set up to your laptop kind.
» MORE: DJI Assistant 2: A Full Information (Step-by-Step)
Air 3 Firmware Downgrade (If Out there)
To attach the Air 3 to your PC or Mac for firmware downgrading, you will have the USB to USB-C cable that got here included with the Air 3.
As a aspect observe, the DJI-included USB-C cable each costs the Air 3 and acts as an information cable. The information side of the cable is what connects the Air 3 to the DJI Assistant 2 software program.
Not all third celebration USB-C cables are knowledge cables. So, it’s good to see that DJI has included this explicit cable with all their Air 3 combos and packages.
To attach the Air 3:
Step 1: Insert the Air 3’s USB to USB-C cable into an empty USB slot in your laptop.
Step 2: Whereas the Air 3 is off, plug the USB-C finish into the Air 3.
Step 3: With the Air 3 plugged into an empty USB slot in your PC or Mac, launch the DJI Assistant 2 software program.
Step 4: For first-time utilization of the DJI Assitant 2 Software program, you will have to be logged into your DJI account, which might be achieved within the right-hand nook of the Assistant 2 display screen.
Step 5: After logging into your DJI account or confirming it’s logged in, unfold the Air 3’s legs and arms.
Take away the gimbal cowl and activate the Air 3 by urgent the facility button as soon as after which holding the facility button.
Step 6: The DJI Assistant 2 software program will then launch a display screen that shows an icon representing the Air 3. Select the Air 3.
Step 7: On the left aspect of the display screen select Firmware Replace. You’ll see an inventory of Firmware Variations. If there can be found Firmware variations to downgrade to, you will notice this below the Motion discipline to the appropriate.
» MORE: Use DJI Assistant 2 with DJI Mini 3 / Mini 3 Professional (Step-by-Step Information)
Distant Controller Firmware Downgrade (If Out there)
In case you are wanting to make use of the DJI Assistant 2 software program along with your DJI RC 2 or RC-N2:
Step 1: Insert the Air 3’s USB to USB-C cable into an empty USB slot in your laptop.
Step 2: Whereas the RC 2 or RC-N2 is off, plug the USB-C finish into both the RC 2 or RC-N2. Activate the distant controller.
Step 3: With the RC 2 or RC-N2 plugged into an empty USB slot in your PC or Mac, launch the DJI Assistant 2 software program.
Step 4: The DJI Assistant 2 software program will then transition to a display screen that reveals both your RC 2 or RC-N2. Select your distant controller.
Step 5: On the left aspect of the display screen select Firmware Replace. You’ll see an inventory of Firmware Variations. If there can be found Firmware variations to downgrade to, you will notice this below the Motion discipline to the appropriate.
» MORE: Downgrade Your DJI Firmware Utilizing DJI Assistant 2 (Defined)
DJI RC 2 Manufacturing unit Reset
In contrast to the Air 3 and the RC-N2, the DJI RC 2 can be manufacturing facility reset. As a result of the RC 2 is principally an Android sensible gadget, it’s fairly simple to reset the distant controller.
Notice: Manufacturing unit resetting the DJI RC 2 doesn’t roll again the present firmware. It removes all saved consumer info and knowledge from the distant controller.
To manufacturing facility reset the DJI RC 2, comply with these steps:
STEP 1: After powering on the RC 2, contact the highest of the display screen and slide down twice. This may convey you to the notifications display screen.
STEP 2: Faucet the settings icon on the highest right-hand nook of the display screen.
This may open the settings display screen.
STEP 3: Faucet the System possibility on the backside of the display screen.
STEP 4: Faucet Reset Choices
STEP 5: Press Erase all knowledge (manufacturing facility reset)
STEP 6: You’ll then be introduced with an inventory of what’s going to be erased from the distant controller. Select Erase all knowledge.
After these steps have been accomplished, the DJI RC 2 can be “again to new situation”, from a software program standpoint.
» MORE: Fly DJI Air 3 Drone (With DJI RC 2)
Planning on Promoting or Gifting your Air 3 and DJI RC 2?
Though the Air 3 is a comparatively new drone, there could also be these wishing to present/present it to members of the family, or maybe even promote their Air 3 on-line.
When doing so, along with wiping the info from the DJI RC 2, the Air 3 and RC 2 ought to likewise be unbound from the DJI account and the DJI Profile faraway from the RC 2 distant controller.
» MORE: What to do Earlier than Promoting Your Drone? Learn This First!
Unbinding Units
To unbind the Air 3 and DJI RC 2:
Step 1: Activate the Air 3 and DJI RC 2. Go to your Profile.
Step 2: Within the DJI Profile, faucet System Administration.
Step 3: Select the DJI Air 3 (you probably have a number of drones).
Step 4: Choose Take away System from Account and the Air 3 and DJI RC 2 can be eliminated out of your DJI Account.
» MORE: When Ought to You Improve Your Drone? (Learn This First)
DJI Profiles
The final step of the method can be to take away any traces of your DJI profile from the DJI RC 2.
To take away your present DJI Account info from the DJI RC 2:
STEP 1: Boot up the DJI RC 2. As soon as within the DJI Fly app, go to the Profile icon on the backside of the display screen.
STEP 2: When on the Profile display screen, scroll down on the right-hand aspect till you see the Settings tab. Go into Settings.
STEP 3: Select Log Out on the left aspect of the display screen.
STEP 4: Affirm you want to Log Out of your DJI account. You at the moment are achieved.
This may promptly take away your private info and flight knowledge from the DJI RC 2. The knowledge won’t be deleted out of your precise profile, as this info is linked to the consumer account and never the Air 3.
» MORE: The place Is the Serial Quantity on DJI Air 3 (Answered)
